Appendix BE8102

Read the in-depth information about
the wrist receiver and charger.

Wrist Receiver and Charger

The Visit Wrist Receiver and Charger
Art. no. BE8102

Appendix

Further information

Settings

No adjustments are required for normal use. The relevant descriptions are provided below, if you wish to change a setting for some reason.

Radio key

In order to use several Visit Systems close to one another without interference, different Radio Keys can be set on the different systems. All Visit System units are supplied from the factory tuned to the same Radio Key, channel 0. This means that all Radio Key Switches on the transmitters are set to the OFF position.

A Visit transmitter is also required to alter the Radio Key on the Wrist Receiver.

Proceed as follows to change the Radio Key: 

  1. Set a Visit Transmitter to the desired Radio Key by altering its Radio Key Switch to the desired Radio Key. See the transmitter user manual for further information. 
  2. Hold down the Function Button (1) on the Wrist Receiver until the green (3) and yellow (4) LEDs blink alternately. Release the button and the Visit Wrist Receiver will now be in programming mode for about 30 seconds.
  3. Press the Visit transmitter’s test button.
  4. The LEDs (2, 3, 4 and 5) will now blink five times in quick succession to indicate a successful change of radio key. 
  5. After changing the Radio Key, the Wrist Receiver will automatically return to normal mode.

Please note:red triangle

All Bellman Visit products within the same system must be tuned to the same Radio Key in order to operate as a group.

Signal pattern

A Signal Pattern is the name for the way in which a receiver in the Bellman Visit System indicates activation. Changing the transmitters’ Signal Switch changes the Signal Pattern which the receivers display when the transmitter is activated. 

TypeLED patternSoundVibrationFlash
The following signal patterns are available for the Visit System: (Please note that the Wrist Receiver does not emit any sound or flash.)
Green 1 Green is constantly lit 1 x ding dong, low-frequency tone Separate Yes
Green 2 Green blinks in sequences of two  2 x ding dong, low-frequency tone Separate Yes
Green 3 Green blinks in sequences of three  1 x ding dong, high-frequency tone Separate Yes
Green 4 Green blinks constantly  2 x ding dong, high-frequency tone Separate Yes
Yellow 1 Yellow is constantly lit 1 x ring, low-frequency tone Short Yes
Yellow 2 Yellow blinks in sequences of two  2 x ring ring, low-frequency tone Short Yes
Yellow 3 Yellow blinks in sequences of three  1 x ring, high-frequency tone Short Yes
Yellow 4 Yellow blinks constantly 2 x ring ring, high-frequency tone Short Yes
Orange 1 Orange is constantly lit  Baby Rapid Yes
Orange 2 Orange blinks in sequences of two  Baby Rapid Yes
Orange 3 Orange blinks in sequences of three  Baby Rapid Yes
Orange 4 Orange blinks constantly  Baby Rapid Yes
VMA  Red and Orange constantly blink alternately  VMA constant Long Yes
Fire alarm Red blinks constantly  Fire alarm constant Long Yes
Fire alarm low battery Red blinks every five seconds No No No
Fire alarm flat battery Red blinks every five seconds Fire alarm one short One short Yes

 

Advanced programming

Advanced programming provides additional options for those who wish to make special modifications to the Visit Wrist Receiver.

The idea is that it should be possible to select a completely unique signal pattern which is linked to activation from a specific input on a specific Visit transmitter. The function works regardless of the Radio Key settings on the units that are programmed. Please note that, for safety reasons, the function does not work with the BE1480 Visit Smoke Alarm.

By using advanced programming of the Wrist Receiver, it can be adjusted so that its signal pattern corresponds exactly to what is required. In other words, an entirely individual signal pattern can be programmed, such as displaying a permanently lit orange LED and a constant vibration.

In order to adjust the setting, the Visit Transmitter to which the Visit Wrist Receiver should be adapted must be available. The transmitter must also be connected so that it can be activated in the way in which it is intended to be used.
Proceed as follows:

  1. Hold down the Function Button (1) on the Visit Wrist Receiver until the green (3) and yellow (4) LEDs blink alternately. The Wrist Receiver will now be in programming mode for about 30 seconds.
  2. Hold down the Function Button (1) at the same time as the relevant Visit transmitter is activated in precisely the way in which it is intended to be used. The yellow LED (6) will light up. Note that all inputs are individual, so that it is not possible to use the test button on a Telephone Transmitter whose telephone input will indicate the relevant pattern. 
  3. Scroll through the different LED options by a short press on the Function Button (1). Select the relevant indication by holding down the Function Button (1) until the LED (6) goes out and starts to shine with a constant yellow light again. 
  4. Scroll through the different vibration options by a short press on the Function Button (1). Select the relevant indication by holding down the Function Button (1) until the LED (6) goes out and starts to shine with a constant yellow light again.
  5. The Wrist Receiver will now show the indication method programmed. End the display with a short press of the Function Button (1).
  6. After a short while the Wrist Receiver will automatically return to normal mode.

This function is essential where a transmitter has to work in a special way with regard to a specific receiver. 

Resetting advanced programming

It is to reset the Wrist Receiver if it needs to be reset after it has been programmed using advanced programming.

  1. Hold down the Function Button (1) on the Visit Wrist Receiver until the green (3) and yellow (4) LEDs blink alternately. The Wrist Receiver will now be in programming mode for about 30 seconds.
  2. Press the Function Button (1) three times in quick succession.
  3. All LEDs (2-5) remain constantly on for a few seconds.
  4. All the advanced programming has now been deleted and the Wrist Receiver will automatically return to normal mode.

Testing

It is easy to test the BE1560 Visit Wrist Receiver. If the Wrist Receiver does not work as described below, you can check further below under Appendix/Further information/Troubleshooting/Troubleshooting guide.

How to test

A transmitter in the Visit System which is set to the same Radio Key as the Wrist Receiver is required to test the radio reception on the BE1560 Visit Wrist Receiver. 

  1. Press the transmitter test button.
  2. The Visit Wrist Receiver will give the following indications:
  • The LEDs (2-5) which the transmitter has been set to indicate with or which have been programmed into the Visit Wrist Receiver with Advanced Programming will be switched on.
  • It will vibrate as the transmitter is set to indicate or in the way the Visit Wrist Receiver has been programmed with advanced programming.

Troubleshooting

You can carry out a number of checks yourself before sending a product for repair. 

Troubleshooting guide
ProblemSolution
Nothing happens                     
  • Check that the power supply unit is connected correctly and that the green LED (10) on the Charger lights up.
  • Charge or renew the battery in the Wrist Receiver. Only use a rechargeable VARTA V40H NiMH battery. If the battery is completely flat, you can still use the Wrist Receiver by placing it in the Charger. The Wrist Receiver needs to be charged for about two hours before it can be used separately.
  • Check that the Wrist Receiver has been correctly placed in the Wrist Receiver Charger and that the LED (12) lights up green
It is not possible to charge the Wrist Receiver.
  • Check that the power supply unit is connected correctly and that the green LEDs (10 and 12) on the Charger light up
  • Charge or change the batteries in the Wrist Receiver Charger. Only use rechargeable TMK AAA60CT NiMH batteries.
Nothing happens when the power supply unit is disconnected. Nor does the Test Button (11) work.
  • Charge or change the batteries. Only use rechargeable TMK AAA60CT NiMH batteries.
The LED (6) on the Wrist Receiver blinks yellow.
  • Charge or renew the battery in the Wrist Receiver. Only use a rechargeable VARTA V40H NiMH battery. If the battery is completely flat, you can still use the Wrist Receiver by placing it in the Charger. The Wrist Receiver needs to be charged for about two hours before it can be used separately.
The Bed-shaker does not vibrate when the Wrist Receiver is activated.
  • Check that the bed-shaker is correctly connected to the Wrist Receiver Charger.
  • Check that the Wrist Receiver has been correctly inserted in the Wrist Receiver Charger and that the LED (12) lights up green.
The Wrist Receiver does not pick up signals from the Visit Transmitters.
  • Check the batteries in the transmitters.
  • Check that the Wrist Receiver is not placed too far away by moving it closer to the transmitter.
  • Check that the Wrist Receiver is set to the same Radio Key as the other units in the relevant Visit System. For further information see Appendix/Further information/Settings/Radio key.
The Wrist Receiver is emitting the wrong signals, regardless of how the transmitter is set.
  • Delete the advanced programming, see Appendix/Further information/Resetting advanced programming.
The receiver signals when no transmitter is activated.
  • Change the Radio Key on all units in the relevant Visit System. There is probably another system nearby with the same Radio Key.

 

RESOURCES
 MANUAL DATA SHEET (EN)