Appendix BE1510
Read the in-depth information about
the Visit repeater.
Read the in-depth information about
the Visit repeater.
The BE1510 Visit Repeater has the following methods of activation:
For more information about the indications provided by the receivers in the Visit System, refer to Appendix/Further information/Settings below.
An Exterior External Trigger on the Repeater can be connected to the vibrator output on several of Bellman & Symfon AB’s products or to other equipment that produces a voltage or contact for activation. In addition, the following accessories can be used:
No adjustments are required for normal use. The relevant descriptions are provided below, if you wish to change a setting for some reason.
In order to use several Bellman Visit Systems close to one another without interference, different Radio Keys can be set on the different systems. All Bellman Visit System units are supplied from the factory tuned to the same Radio Key, channel 0. This means that all Radio Key Switches on the transmitters are set to the OFF position.
All Bellman Visit products within the same system must be tuned to the same Radio Key in order to operate as a group.
A Signal Pattern is the name for the way in which a receiver in the Bellman Visit System indicates activation. Changing the transmitters’ Signal Switch changes the Signal Pattern which the receivers display when the transmitter is activated. Follow the instructions under Appendix/Further information/Settings/Setting the activation pattern to make your choice.
Type | LED pattern | Sound | Vibration | Flash |
---|---|---|---|---|
Green 1 | Green is constantly lit | 1 x ding dong, low-frequency tone | Separate | Yes |
Green 2 | Green blinks in sequences of two | 2 x ding dong, low-frequency tone | Separate | Yes |
Green 3 | Green blinks in sequences of three | 1 x ding dong, high-frequency tone | Separate | Yes |
Green 4 | Green blinks constantly | 2 x ding dong, high-frequency tone | Separate | Yes |
Yellow 1 | Yellow is constantly lit | 1 x ring, low-frequency tone | Short | Yes |
Yellow 4 | Yellow blinks constantly | 2 x ring ring, high-frequency tone | Short | Yes |
Orange 1 | Orange is constantly lit | Baby | Rapid | Yes |
Orange 2 | Orange blinks in sequences of two | Baby | Rapid | Yes |
Orange 3 | Orange blinks in sequences of three | Baby | Rapid | Yes |
Orange 4 | Orange blinks constantly | Baby | Rapid | Yes |
VMA | Red and Orange constantly blink alternately | VMA constant | Long | Yes |
Fire alarm | Red blinks constantly | Fire alarm constant | Long | Yes |
The Repeater can be activated in two different ways.
On delivery the Repeater sends the same signal regardless of the input causing the activation.
By changing the Signal Switches (4), different inputs on the same Repeater can transmit different Signal Patterns.In this way the same Repeater can be used to forward signals from the Visit System at the same time as it can transmit a Door Signal when activated via the Exterior External Trigger (3) and a Baby Cry signal when activated via the Test Button (2).
Signal pattern on activation from: | ||
---|---|---|
Signal switch | Exterior external trigger | Pushbutton |
![]() |
Green 1 | Green 1 |
![]() |
Green 2 | Green 2 |
![]() |
Green 3 | Green 3 |
![]() |
Green 4 | Green 4 |
![]() |
Orange 1 | Green 4 |
![]() |
Orange 2 | Green 3 |
![]() |
Orange 3 | Green 2 |
![]() |
Orange 4 | Green 1 |
![]() |
Green 1 | Orange 1 |
![]() |
Green 2 | Orange 2 |
![]() |
Green 3 | Orange 3 |
![]() |
Green 4 | Orange 4 |
![]() |
Green 1 | Yellow 1 |
![]() |
Green 4 | Yellow 4 |
![]() |
VMA | VMA |
![]() |
Fire alarm | Fire alarm |
It is easy to test the Visit Repeater. If the Repeater does not work as described below, you can check further under Troubleshooting/Troubleshooting guide.
A transmitter in the Visit System which is set to the same radio key as the Repeater is required to test the radio reception on the BE1510 Visit Repeater.
To test the Transmitter:
You can carry out a number of checks yourself before sending a product for repair.
Problem | Solution |
---|---|
Nothing happens when the transmitter is activated with the test button(2). |
|
The LED (1) blinks yellow when the Repeater is activated. |
|
The LED (1) blinks green when the Repeater is activated, but the receivers are not signalling. |
|
The receiver emits a strange alarm when activated by the Repeater. |
|
The receiver signals when no transmitter is activated. |
|
MANUAL |