Appendix BE1470

Read the in-depth information about
the pager.

Pager

The Visit Pager
Art. no. BE1470

Appendix

Further information

Settings

No adjustments are required for normal use. The relevant descriptions are provided below, if you wish to change a setting for some reason.

Radio key

In order to use several Visit Systems close to one another without interference, different Radio Keys can be set on the different systems. All Visit System units are supplied from the factory tuned to the same Radio Key, channel 0. This means that all Radio Key Switches on the transmitters are set to the OFF position.

A Visit transmitter is also required to alter the radio key on the Visit Pager. Proceed as follows to change the Radio Key: 

  1. Set a Visit Transmitter to the desired radio key by altering its radio key switch to the desired radio key. See the transmitter user manual for further information. 
  2. Hold down the function button (1) on the Pager until the green (3) and yellow (4) LEDs blink alternately. The Pager will now be in programming mode for about 30 seconds.
  3. Press the transmitter’s test button.
  4. The LEDs (2, 3, 4 and 5) will now blink five times in quick succession to indicate a successful change of radio key. 
  5. After changing the radio key, the Pager will automatically return to normal mode.

Please note:red triangle

All Bellman Visit products within the same system must be tuned to the same Radio Key in order to operate as a group.

Signal pattern

A Signal Pattern is the name for the way in which a receiver in the Bellman Visit System indicates activation. Changing the transmitters’ Signal Switch changes the Signal Pattern which the receivers display when the transmitter is activated. 

Type LED pattern Sound Vibration Flash
The following signal patterns are available for the Visit System: (Note that the Pager does not emit any sound or flash)
Green 1 Green is constantly lit 1 x ding dong, low-frequency tone Separate Yes
Green 2 Green blinks in sequences of two  2 x ding dong, low-frequency tone Separate Yes
Green 3 Green blinks in sequences of three  1 x ding dong, high-frequency tone Separate Yes
Green 4 Green blinks constantly  2 x ding dong, high-frequency tone Separate Yes
Yellow 1 Yellow is constantly lit 1 x ring, low-frequency tone Short Yes
Yellow 2 Yellow blinks in sequences of two  2 x ring ring, low-frequency tone Short Yes
Yellow 3 Yellow blinks in sequences of three  1 x ring, high-frequency tone Short Yes
Yellow 4 Yellow blinks constantly 2 x ring ring, high-frequency tone Short Yes
Orange 1 Orange is constantly lit  Baby Rapid Yes
Orange 2 Orange blinks in sequences of two  Baby Rapid Yes
Orange 3 Orange blinks in sequences of three  Baby Rapid Yes
Orange 4 Orange blinks constantly  Baby Rapid Yes
VMA  Red and Orange constantly blink alternately  VMA constant Long Yes
Fire alarm Red blinks constantly  Fire alarm constant Long Yes
Fire alarm low battery Red blinks every five seconds No No No
Fire alarm flat battery Red blinks every five seconds Fire alarm one short One short Yes

 

Advanced programming

Advanced programming provides additional options for those who wish to make special modifications to the Flash Receiver.
The idea is that it should be possible to select a completely unique signal pattern which is linked to activation from a specific input on a special Visit transmitter. The function works regardless of the radio key settings on the units that are programmed. Please note that, for safety reasons, the function does not work with the BE1480 Visit Smoke Alarm.

By using advanced programming of the Pager, it can be adjusted so that its signal pattern corresponds exactly to what is required. In other words an entirely individual signal pattern can be programmed, such as displaying an orange permanently lit LED and a constant vibration.In order to adjust the setting, the Visit Transmitter to which the Visit Pager should be adapted must be available. The transmitter must also be connected so that it can be activated in the way in which it is intended to be used.
Proceed as follows:

  1. Hold down the Function Button (1) on the Visit Pager until the green (3) and yellow (4) LEDs blink alternately. The Visit Pager will now be in programming mode for about 30 seconds.
  2. Hold down the Function Button (1) at the same time as the relevant Visit transmitter is activated in precisely the way in which it is intended to be used. The yellow LED (6) will light up. Note that all inputs are individual, so that it is not possible to use the test button on a Visit Telephone Transmitter whose telephone input will indicate the relevant pattern.
  3. Scroll through the different LED options by a short press on the Function Button (1). Select the relevant indication by holding down the Function Button (1) until the LED (6) goes out and starts to shine with a constant yellow light again.
  4. Scroll through the different vibration options by a short press on the Function Button (1). Select the relevant indication by holding down the Function Button (1) until the LED (6) goes out and starts to shine with a constant yellow light again.
  5. The Pager will now show the indication method programmed. End the display with a short press of the Function Button (1).
  6. After a short while, the Pager will automatically return to normal mode.

This function is essential where a transmitter has to work in a special way with regard to a specific receiver. 

Resetting advanced programming

It is quite to reset the Pager if it needs to be reset after it has been programmed using advanced programming.

  1. Hold down the Function Button (1) on the Pager until the green (3) and yellow (4) LEDs blink alternately. The Pager will now be in programming mode for about 30 seconds.
  2. Press the Function Button (1) three times in quick succession.
  3. All LEDs (2-5) remain constantly on for a few seconds.
  4. All the advanced programming has now been deleted and the Visit Pager will automatically return to normal mode.

Testing

It is easy to test the Flash Receiver. If the unit does not work as described below, you can check further under Troubleshooting/Troubleshooting guide.

How to test

A transmitter in the Visit system which is set to the same radio key as the Pager is required to test the radio reception on the BE1470 Visit Pager. 

  1. Press the transmitter test button.
  2. The Visit Pager will give the following indications:
  • The LEDs (2-5) which the transmitter has been set to indicate with or which have been programmed into the Pager with Advanced Programming will be switched on.
  • It will vibrate as the transmitter is set to indicate or in the way the Pager has been programmed with advanced programming.

Troubleshooting

You can carry out a number of checks yourself before sending a product for repair. 

Troubleshooting guide
ProblemSolution
Nothing happens 
  • Change or charge the battery. Only use an alkaline AAA type battery or a rechargeable NiMh AAA type battery
The LED (6) blinks yellow.
  • Change or charge the battery. Only use an alkaline AAA type battery or a rechargeable NiMh AAA type battery
The Pager does not pick up signals from the Visit Transmitters.
  • Check that the Pager is set to the same radio key as the other units in the relevant Visit system. For further information see Appendix/Further information/Settings/Radio key.
  • Check the batteries in the transmitters.
  • Check that the pager is not placed too far away by moving it closer to the transmitter.
The receiver signals when no transmitter is activated.
  • Change the Radio Key on all units in the relevant Bellman Visit 868 System. There is probably another system nearby with the same Radio Key.

 

RESOURCES
 MANUAL
DATA SHEET (EN)