Read the in-depth information.
Read the in-depth information.
No adjustments are required for normal use. The relevant descriptions are provided below, if you wish to change a setting for some reason.
In order to use several Visit Systems close to one another without interference, different Radio Keys can be set on the different systems. All Visit System units are supplied from the factory tuned to the same Radio Key, channel 0. This means that all Radio Key Switches on the transmitters are set to the OFF position. A Visit transmitter is also required to alter the radio key on the Visit Flash Receiver.
Proceed as follows to change the Radio Key:
All Bellman Visit products within the same system must be tuned to the same Radio Key in order to operate as a group.
A Signal Pattern is the name for the way in which a receiver in the Bellman Visit System indicates activation. Changing the transmitters’ Signal Switch changes the Signal Pattern which the receivers display when the transmitter is activated.
|Green 1||Green is constantly lit||1 x ding dong, low-frequency tone||Separate||Yes|
|Green 2||Green blinks in sequences of two||2 x ding dong, low-frequency tone||Separate||Yes|
|Green 3||Green blinks in sequences of three||1 x ding dong, high-frequency tone||Separate||Yes|
|Green 4||Green blinks constantly||2 x ding dong, high-frequency tone||Separate||Yes|
|Yellow 1||Yellow is constantly lit||1 x ring, low-frequency tone||Short||Yes|
|Yellow 2||Yellow blinks in sequences of two||2 x ring ring, low-frequency tone||Short||Yes|
|Yellow 3||Yellow blinks in sequences of three||1 x ring, high-frequency tone||Short||Yes|
|Yellow 4||Yellow blinks constantly||2 x ring ring, high-frequency tone||Short||Yes|
|Orange 1||Orange is constantly lit||Baby||Rapid||Yes|
|Orange 2||Orange blinks in sequences of two||Baby||Rapid||Yes|
|Orange 3||Orange blinks in sequences of three||Baby||Rapid||Yes|
|Orange 4||Orange blinks constantly||Baby||Rapid||Yes|
|VMA||Red and Orange constantly blink alternately||VMA constant||Long||Yes|
|Fire alarm||Red blinks constantly||Fire alarm constant||Long||Yes|
|Fire alarm low battery||Red blinks every five seconds||No||No||No|
|Fire alarm flat battery||Red blinks every five seconds||Fire alarm one short||One short||Yes|
Advanced programming provides additional options for those who wish to make special modifications to the Flash Receiver.
The idea is that it should be possible to select a completely unique signal pattern which is linked to activation from a specific input on a special Visit transmitter. The function works regardless of the radio key settings on the units that are programmed. Please note that, for safety reasons, the function does not work with the BE1480 Visit Smoke Alarm.
By using advanced programming of the Flash Receiver, it can be adjusted so that its signal pattern corresponds exactly to what is required. In other words an entirely individual signal pattern can be programmed, such as displaying an orange permanently lit LED and a constant vibration.
In order to adjust the setting, the Visit Transmitter to which the Visit Flash Receiver should be adapted must be available. The transmitter must also be connected so that it can be activated in the way in which it is intended to be used.
Proceed as follows:
This function is essential where a transmitter has to work in a special way with regard to a specific receiver.
It is easy to reset the Visit Flash Receiver if it needs to be reset after it has been programmed using advanced programming.
It is easy to test the Flash Receiver. If the unit does not work as described below, you can check further under Troubleshooting/Troubleshooting guide.
A transmitter in the Visit System which is set to the same Radio Key as the Flash Receiver is required to test the flashing light and vibration, if the BE1270 Bellman Bed-shaker (accessory) is connected, and the radio reception on the BE1440 Visit Flash Receiver.
To test the analogue telephone input:
A short press on the Test Button (9) activates BE1440 so that it repeats its last indication.
You can carry out a number of checks yourself before sending a product for repair.
|The Flash Receiver does not pick up signals from the Visit Transmitters.
|The receiver signals when no transmitter is activated.||
||DATA SHEET (EN)