Appendix BE1410

Read the in-depth information about the
door transmitter

Door Transmitter

The Visit Door Transmitter
Art. no. BE1410

Appendix

Further information

Connection

Connecting an External Microphone

The BE1410 Visit Door Transmitter has an option to connect a BE9199/BE9200 External Door Microphone (accessory) to the Microphone Socket (9). By using the external microphone the Door Transmitter can also pick up sounds from sound sources which are not located close to the Door Transmitter, e.g. door phones and telephones with a suitable ring signal. 

For more information about the indications provided by the receivers in the Bellman Visit System, refer to Appendix/Further information/Settings/Signal pattern and Appendix/Further information/Settings/Setting the activation pattern.

Settings

No adjustments are required for normal use. The relevant descriptions are provided below, if you wish to change a setting for some reason.

Radio key

In order to use several Bellman Visit Systems close to one another without interference, different Radio Keys can be set on the different systems. All Bellman Visit System units are supplied from the factory tuned to the same Radio Key, channel 0. This means that all Radio Key Switches on the transmitters are set to the OFF position.

  • To alter the Radio Key, move the Radio Key Switches (7) to the desired positions.

Please note:red triangle

All Bellman Visit products within the same system must be tuned to the same Radio Key in order to operate as a group.

Signal pattern

A Signal Pattern is the name for the way in which a receiver in the Bellman Visit System indicates activation. Changing the transmitters’ Signal Switch changes the Signal Pattern which the receivers display when the transmitter is activated. Follow the instructions under Appendix/Further information/Settings/Setting the activation pattern to make your choice.

THE FOLLOWING SIGNAL PATTERNS ARE AVAILABLE FOR THE VISIT Door TRANSMITTER BE1410:
TypeLED patternSoundVibrationFlash
Green 1 Green is constantly lit 1 x ding dong, low-frequency tone Separate Yes
Green 2 Green blinks in sequences of two  2 x ding dong, low-frequency tone Separate Yes
Green 3 Green blinks in sequences of three  1 x ding dong, high-frequency tone Separate Yes
Green 4 Green blinks constantly  2 x ding dong, high-frequency tone Separate Yes
Yellow 1 Yellow is constantly lit 1 x ring, low-frequency tone Short Yes
Yellow 2 Yellow blinks in sequences of two  2 x ring ring, low-frequency tone Short Yes
Yellow 3 Yellow blinks in sequences of three  1 x ring, high-frequency tone Short Yes
Yellow 4 Yellow blinks constantly 2 x ring ring, high-frequency tone Short Yes

 

Setting the Activation Pattern

The Door Transmitter can be activated in three different ways.

On delivery the Door Transmitter sends the same signal regardless of the input causing the activation. 
signalswitch illustration
Using the Training Mode, different sounds can make a Door Transmitter transmit different signal patterns according to the sound that has activated the Door Transmitter. For further information see Settings/Sound training.

The figure below shows the standard settings that are available.
     Signal pattern on activation from: 
 Signal switch     

Electromagnetic detection, On(up)

dip1000
Standard,
Int. Mic. 1 and Test button
Int. Mic.2                               Ext.Mic.                          
 dip0000 Off Green 1 Green 4  Green 2 
 dip0001 Off Green 2 Green 2 Yellow 1
 dip0010 Off Green 3 Green 2 Yellow 2 
 dip0011 Off Green 4 Green 1 Green 3
 dip0100 Off Green 1 Green 3 Green 4 
 dip0101 Off Green 2  Green 4 Yellow 4
 dip0110 Off Green 3 Green 1 Yellow 3
 dip0111 Off Green 4 Green 2 Green 1
 dip1000 On Green 1 Green 4 Green 2
 dip1001 On Green 2 Green 3 Yellow 1
 dip1010 On Green 3 Green 2 Yellow 2
 dip1011 On Green 4  Green 1 Green 3
 dip1100 On Green 1 Green Green 4 
 dip1101 On Green 2 Green 4  Yellow 4 
 dip1110 On Green 3 Green 1 Yellow 3
 dip1111 On Green 4 Green 2 Green 1

 

Electromagnetic detection

To further improve the capability of the Door Transmitter, it can detect the electromagnetic fields emitted by an electromechanical doorbell. The advantage of this is a further detection option, which eliminates the risk of missed activations. The Door Transmitter must be mounted 3 cm max. from the doorbell for the best results.

If there is a constant magnetic field close to the Door Transmitter, this will be indicated by the LED (1) blinking orange. In this case turn off electromagnetic detection by setting the first switch on the Signal Switches (6) to OFF. For further information see Appendix/Further information/Settings/Setting the Activation Pattern.

Testing

It is easy to test the Door Transmitter. If the Door Transmitter does not work as described below, you can check further under Troubleshooting/Troubleshooting guide.

How to test

Proceed as follows to check the Door Transmitter’s transmitter:

  • Press the Test Button (2).
  • The Door Transmitter should now light up LED (1) to show that it has been activated and to show that it is transmitting a signal to the receivers in the Bellman Visit System.
  • The receivers in the system will indicate an alarm according to the way that the Door Transmitter has been set up using the Signal Switches (6). 


Proceed as follows to check all Door Transmitter functions:

  • Check that the Door Transmitter is correctly connected. Refer to Getting started/Unpacking, fitting and testing the unit for connection instructions.
  • Activate the Door Transmitter with the relevant doorbell.
  • The Door Transmitter should now light up LED (1) to show that it has been activated and to show that it is transmitting a signal to the receivers in the Bellman Visit System.
  • The receivers in the system will indicate an alarm according to the way that the Door Transmitter has been set up using the Signal Switches (6). 

Troubleshooting

You can carry out a number of checks yourself before sending a product for repair. 

Troubleshooting guide
ProblemSolution
Nothing happens when the transmitter is activated with the test button.
  • The Door Transmitter waits until it has been quiet for two seconds in order to avoid acoustic feedback. Try again.
  • Change the battery. Only use an alkaline 6LR61 or a lithium 6F22 type battery.
  • Check that all the connections are correct.
The LED (1) lights up yellow when the Door Transmitter is activated.
  • Change the battery. Only use an alkaline 6LR61 or a lithium 6F22 type battery.
The LED (1) lights up green when the Door Transmitter is activated, but the receivers are not signalling.
  • Check the battery in the receiver.
  • Check that all units in the Bellman Visit System are set to the same Radio Key. For further information see Appendix/Further information/Settings/Radio key.
  • Check that the receivers are not placed too far away by moving them closer to the transmitter.
The receiver emits an alarm with a different signal pattern from the one expected when it is activated by the Door Transmitter.
  • Set the Signal Switch to X000 to obtain the factory setting. If the Training function is used, this can be deleted as indicated in the instructions under Function/Resetting the trained sound.
The doorbell rings but the Door Transmitter is not activated.
  • Move the Door Transmitter around the doorbell both closer and further away. The normal distance is about 3 cm from the doorbell.
  • Try to train the Door Transmitter with the relevant doorbell sound. For further information see Function/Sound training.
  • Does the doorbell have a ring signal which varies significantly in strength and/or tone? In this case it may be difficult to detect this doorbell using the training function. Try resetting the Door Transmitter to standard. For further information see Function/Resetting the trained sound.
  • Rectify the problem as indicated in the descriptions under Function/General and Function/Using the Bellman External Door Microphone BE9199/BE9200.
The door transmitter is activated when the doorbell is not ringing.
  • Turn off the magnetic coil if an electromagnetic field from an inductive loop, etc., is causing activation. For further information see Appendix/Further information/Settings/Electromagnetic detection.
  • Try to train the Door Transmitter with the relevant doorbell sound. For further information see Function/Sound training.
  • Rectify the problem as indicated in the descriptions under Function/General and Function/Using the Bellman External Door Microphone BE9199/BE9200.
The LED (1) blinks yellow.
  • Make sure that it is quiet by the Door Transmitter.
  • Turn off the magnetic coil if an electromagnetic field from an inductive loop, etc., is causing a fault to be indicated. 
  • Disconnect the External Microphone in case a faulty microphone is connected.
The receiver signals when no transmitter is activated.
  • Change the Radio Key on all units in the relevant Bellman Visit System. There is probably another system nearby with the same Radio Key.

 

RESOURCES
 MANUAL DATA SHEET (EN)